[Aug-2022 Newly Released] NACE-CIP2-001 Exam Questions For You To Pass [Q51-Q67] : Free valid test braindumps : http://free.validbraindumps.com

NO.51 Linings are used on the interior of pipelines to

provide protection against soil chemicals.

afford limited temperature insulation.

protect the transported product.

reduce magnetic polarity.

NO.52 Surface preparation methods for Non-ferrous metals are:

The same as for Ferrous metals

The same for all Non-FetT0us metals

Specific for each type of Non-ferrous metal

Not required

NO.53 You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:

Refuse to take readings until an is in place

Develop your own methodology and proceed take the readings

Use a generally accepted industry standard and to take readings

Call your supervisor

NO.54 You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:

Correct the errors yourself and suggest the Level 1 inspector be replaced

Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent

Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation

Correct the errors yourself and submit the reports without any further action

NO.55 NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:

True

False

NO.56 You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:

Request that the Contractor re-blast the floor

Review the standard with the Contractor and re-inspect the floor

Shut the job down

Call your supervisor

NO.57 On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?

Liquid epoxies

Heat-shrink sleeves

Concrete

Coal Tar Enamel

NO.58 Inspection and Test plans are developed by referencing:

The Specification, TDS, relevant Standards and Codes

The Specification, SDS, relevant Standards and Codes

The Specification, Application Guidelines, ‘Relevant Standards and Codes

The Specification, Safety Manual, Relevant Standards and Codes

NO.59 The Concrete Repair Institute’s comparators can be used to assess:

Surface cleanliness prior to coating

Surface profile prior to coating

Contamination levels prior to coating

Compressive and tensile strength prior to coating

NO.60 In which type of concrete are laitance commonly encountered?

Concrete block (poured with a form)

Gunite

Glass fiber cement

Poured (wet cast)

NO.61 An Inspection and Test Plan is required when:

It is always required

When the Coating Applicator requests one

When the Owner specifies one

When the Inspector requests one

NO.62 Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?

Sacking

Acid etching

Stoning

High-pressure water washing

NO.63 Examples of non-ferrous metals include
Select All that Apply:

mild steel.

aluminum

iron

copper

NO.64 A reinforced coating is

equally resistant to movement and impact as a non-reinforced coating.

equally resistant to abrasion and impact as a non-reinforced coating.

less resistant to movement, abrasion, and impact than a non-reinforced coating.

more resistant to movement, abrasion, and impact than a non-reinforced coating.

NO.65 NACE Standards include:

Standard Practices

Material Requirements

a) & b)

a) only

NO.66 You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:

Risk of chemical exposure

Risk of skin

Risk of acid or caustic splashes

a), b), and c)

NO.67 Which standards are generally established by private-sector bodies and are available for use by any person or Organization, private or government?

Consensus

Mandatory

De facto

Voluntary