Validate your 300-510 Exam Preparation with 300-510 Practice Test (Online & Offline) [Q43-Q58] : Free valid test braindumps : http://free.validbraindumps.com

Q43. Refer to the exhibit. R3 is:
* failing to accept multicast RP information from Domain-A
* advertising MSDP SA messages to R1 and R4
* receiving SA messages only from R4
Which command must the engineer implement to resolve the issue?

R3# ip msdp sa-filter in 192.168.3.1

R3# no ip msap sa-filter in 192.168.1.1

R3# no ip msdp peer 192.168.1.1

R3# ip msdp sa-filter out 192.168.1.1

Q44. Which statement about enabling segment routing for IGPs is true?

Segment routing must first be enabled under then routing process and then globally

Segment routing must first be enabled globally and then under the routing process

Segment routing can be enabled only under the routing process

Segment routing can be enabled only globally

Q45. Refer io the exhibit. While applying the configurations on two routers an engineer notices that OSPF adjacency Between them remains down. Through the ping test the engineer confirmed that both me routers have Layer 3 reachability between them. Which action should me engineer take to make the adjacencies to full?

Enter the command ip ospf authentication in R2 interface

Enable OSPF just inside the router OSPF process not in the interfaces of any router

Delete the area 0 authentication message-digest command from the OSPF process in R1

Delete the area 0 authentication message-digest command from the OSPF process in R2

Q46. Refer to the exhibit.

Which attribute can router 1 alter so that only other iBGP peers prefer to use 192.168.4.2 as the next hop for route 192.168.3.0/24?

MED

local preference

origin

weight

Q47. In a PIM-SM environment, which mechanism determines the traffic that a receiver receives?

The receiver explicitly requests its desired traffic from the RP on the shared tree.

The receiver explicitly requests traffic from a single source, which responds by forwarding all traffic.

The RP on the shared tree floods traffic out of all PIM configured interfaces.

The receiver explicitly requests traffic from each desired source, which responds by sending all traffic.

Q48. Refer to the exhibit.

The green policy is designed with low delay, and the pink policy is designed with low cost. What is the next hop for node A on its way to node D, with the objective of achieving a low delay?

192.168.3.2

192.168.1.6

192.168.3.6

192. 168.1.2

Q49.

Refer to the exhibit. R1 is directly connected to R2 and R3. R1 is in BGP AS 123, R2 is in BGP AS 2, and R3 is in BGP AS 3. Assume that there is no connectivity issue between R1, R2 and R1, R3. Which result between BGP peers R1, R2 and R1, R3 is true?

The BGP session does not come up between R1 and R2 and between R1 and R3.

The BGP session comes up between R1 and R2 and between R1 and R3.

The BGP session comes up between R1 and R3, but not between R1 and R2.

The BGP session comes up between R1 and R2, but not between R1 and R3.

Q50. Refer to the exhibits. All links inside the network are configured at a default cost of one inside the fully converged OSPF domain. Given the configuration from XR1, which interface does traffic from XR1 that is destined to the loopback interface of XR6 select for the exiting interface?

Interface GigabitElhemet 0/0. The tie breaker of the node index priority is lower and trumps the path cost.

Interface GigabitEthernet 0/1. The tie breaker of the path cost being lower. The node index priority does not impact this selection process.

Interface GigabitEthernet 0/1. The tie breaker of the node index priority is lower and trumps the path cost.

Interface GigabitEthernet 0/0. The tier breaker of the path cost being lower. The node index priority does not impact this selection process.

Q51. Which difference should be considered when intradomain or interdomain multicast routing is implemented?

Interdomain multicast routing requires an IS-IS or OSPF neighbor relationship between the domains but intradomain multicast routing requires only BGP Questions & Answers PDF P-57

Interdomain multicast routing relies on PIM-DM and intradomain multicast routing relies on PIM- SM.

interdomain multicast routing uses BIDR-PIM to establish neighbor relationships between AS and interdomain multicast routing uses MSDP

A network uses intradomain multicast routing without interdomain routing but networks that use interdomain multicast routing must also apply intradomain routing

Q52. Refer to the exhibit.

Which task must you perform on interface g1/0/0 to complete the SSM implementation?

configure OSPFv3

enable CDP

disable IGMP

configure IGMPv3

Q53. Refer to the exhibit.

After these configurations were applied to routers R1 and R2. the two devices cannot form a neighbor relationship What is the reason tor the problem?

The two routers have the same area ID.

The two routers have different iS-types

The two routers have the same network ID

The two routers cannot authenticate with one another

Q54. Refer to the exhibit. An engineer is addressing an IS-IS design issue which is running within the topology.
All links are running on FastEthernet, except the link between R5 and R4, which is Gigabit Ethernet.
Which statement about the design is true?

R4 prefer to reach R5 using R1 as the next hop

All links have equal cost if the default metric is used

R5 prefers to use R4 as the next hop for all routes

R1 prefer to use R5 as the next hop to reach R4

Q55. Refer to the exhibit.

Router 1 is a core ABR in a Cisco Unified MPLS environment. All of the router 1 BGP peers are established, but traffic between customers is failing. Which BGP configuration must be added to the configuration?

It must be configured for graceful restart

It must be configured with a route reflector

It must be configured with send labels

It must be configured with PIC edge

Q56. Refer to the exhibit.

A network operator is working to filter routes from being advertised that are covered under an aggregate announcement. The receiving router of the aggregate announcement block is still getting some of the more specific routes plus the aggregate. Which configuration change ensures that only the aggregate is announced now and in the future if other networks are to be added?

Configure the summary-only keyword on the aggregate command

Set each specific route in the AGGRO policy to drop instead of suppress-route

Filter the routes on the receiving router

Set each specific route in the AGGRO policy to remove instead of suppress-route

Q57.

Refer to the exhibit. Which router does R1 install as an alternate next hop when trying to reach R3 if LFA is enabled?

Q58. Refer to the exhibit.

Router 1 has attempted to establish a Cisco MPLS TE tunnel to router 2, but the tunnel has failed. Which statement about this configuration is true?

Router 1 must define an explicit path to router 2

Router 1 and router 2 must define the RSVP bandwidth reserved on the physical interfaces

Router 2 must have a tunnel interface created with router 1 as the destination

Router 1 must have Cisco MPLS TE enabled on interface gigabitethernet0/1

Validate your 300-510 Exam Preparation with 300-510 Practice Test (Online & Offline) [Q43-Q58]

What is the duration, language, and format of Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) Exam

For more info read reference:

Topics of Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) Exam