Online H35-481_V2.0 Test Brain Dump Question and Test Engine [Q24-Q44] : Free valid test braindumps : http://free.validbraindumps.com

NO.24 Which of the following are the functions of SRSs In NR?

Downlink beamforming weight calculation

Uplink grant

To obtain the uplink channel quality

Uplink beam management

NO.25 Which of the following X2 Interconnection solutions are supported by LTE and NR base stations?

Interconnection through RF modules

Interconnection through the a

Interconnected through the backplane in co-BBU separate-MPT scenarios

Interconnection through traditional IP RAN

NO.26 Which of the following synchronization rasters can be used by a UE during a cell search?

17.28MHz

1200kHz

1.44MHz

100kHz

NO.27 Which of the following parameters in core network subscription information restricts the non-GBR rate for a UE?

UE-AMBR

SINR

MBR

GBR

NO.28 Which of the following Information Is not carried In the DCI of NR?

PUSCH scheduling

PUSCH power control

PMI report

PDSCH scheduling

NO.29 When a GPS divider is used, the maximum distance between the GPS antenna and the BBU is shortened.

True

False

NO.30 Which of the following slots retains the same physical position on both the BBU5900 and BBU3910?

SIot6

SIot2

Slot7

Slot1

NO.31 Which of the following scenario using the radio data planning file In the MAE-Deployment?

Configuration of parameters in multiple MOs

Batch reconfiguration of NEs

Reconfiguration of a single NE

Configuration of parameters in an MO

NO.32 Which of the following parameters In the NR MIB message indicates the time-domain position of CORESET
0?

System frame number

Most significant four bits of PDCCH-configSIBl

SSB-subcarrier offset

Least significant four bits of PDCCH-configSIBl

NO.33 Which of the following Information Is contained in a master Information block (MIB)?

System frame number

PDCCH ConfigSIB1

dmrs-TypeA-Position

Offset from PointA

NO.34 In SA networking, which of the following are required after the Pa reconfiguration of a 5G base station?

Checking whether cell-related alarms are reported.

Checking whether the PCI on the LTE side has taken effect on the NE.

Checking whether the 5G cell services are normal.

Checking whether the PCI on the NR side has taken effect on the NE.

NO.35 Which of the following statements about PDSCH DMR5 is incorrect?

The start symbol of a front-loaded DMRS of a type B PDSCH is always the first symbol of PDSCH.

The front-loaded DMRS is mandatory, and the additional DMRS is optional.

The overhead of type 1 DMRS is less than that of type 2 DMRS.

The start symbol of a front-loaded DMRS of a type A PDSCH can be symbol 2.

NO.36 Which of the following 5G network technologies can reduce IoV latency?

MEC

NFV

Massive MIMO

SDN

NO.37 Which of the following boards can be blocked by running the BLK BRD command?

BBP

DUPEU

AAU

RRU

NO.38 Which of the following commands is used to map DSCPs and VLAN priorities?

MOD PHBMAP

SET DSCPMAP

MOD DSCPMAP

SET PHBMAP

NO.39 Which of the following methods is recommended for modifying the cell bandwidths across the entire network during gNodeB data reconfiguration?

MAE-Deployment (radio network planning data file)

MAE-Deployment (batch reconfiguration)

MML

MAE-Deployment (batch reconfiguration + radio network planning data file)

NO.40 Which of the following are possible causes of NRDUCELL unavailability? (Choose All that Apply)

RF fault

BBP fault

Insufficient CPRI bandwidth

Clock exception

NO.41 In the contention-based random access procedure, which of the following is related to the time-frequency position of the PRACH used by the UE?

PCI

BWP

SSB beam ID

C-RNTI

NO.42 The STR CROSFEEDTST command can be used to check for crossed feeder connections of an AAU.

True

False

NO.43 The PING, TRACERT, CFMTRACE, CFMPING, and UDPECHO commands cannot be executed simultaneously on the same board in a gNodeB.

True

False

NO.44 5G can enable smart manufacturing and upgrade the manufacturing business model. Which of the following are smart manufacturing scenarios empowered by 5G?

Real-time operation guidance for industrial AR

Collaborative control between machines

Machine vision positioning & detection

Precise positioning and transportation