This page was exported from Free valid test braindumps [ http://free.validbraindumps.com ] Export date:Sat Apr 5 22:43:51 2025 / +0000 GMT ___________________________________________________ Title: Authentic Fortinet NSE7_EFW-7.0 Exam Dumps PDF - Aug-2023 Updated [Q95-Q114] --------------------------------------------------- Authentic Fortinet NSE7_EFW-7.0 Exam Dumps PDF - Aug-2023 Updated NSE7_EFW-7.0 Dumps Special Discount for limited time Try FOR FREE Q95. Examine the following traffic log; then answer the question below.date-20xx-02-01 time=19:52:01 devname=master device_id=”xxxxxxx”log_id=0100020007 type=event subtype=system pri critical vd=root service=kemel status=failure msg=”NAT port is exhausted.” What does the log mean?  There is not enough available memory in the system to create a new entry in the NAT port table.  The limit for the maximum number of simultaneous sessions sharing the same NAT port has been reached.  FortiGate does not have any available NAT port for a new connection.  The limit for the maximum number of entries in the NAT port table has been reached. Q96. View the exhibit, which contains the output of diagnose sys session list, and then answer the question below.If the HA ID for the primary unit is zero (0), which statement is correct regarding the output?  This session is for HA heartbeat traffic.  This session is synced with the slave unit.  The inspection of this session has been offloaded to the slave unit.  This session cannot be synced with the slave unit. Q97. An administrator added the following Ipsec VPN to a FortiGate configuration:configvpn ipsec phasel -interfaceedit “RemoteSite”set type dynamicset interface “portl”set mode mainset psksecret ENC LCVkCiK2E2PhVUzZenextendconfig vpn ipsec phase2-interfaceedit “RemoteSite”set phasel name “RemoteSite”set proposal 3des-sha256nextendHowever, the phase 1 negotiation is failing. The administrator executed the IKF real time debug while attempting the Ipsec connection.The output is shown in the exhibit.What is causing the IPsec problem in the phase 1?  The incoming IPsec connection is matching the wrong VPN configuration  The phrase-1 mode must be changed to aggressive  The pre-shared key is wrong  NAT-T settings do not match Q98. Refer to the exhibit, which contains the partial output of a diagnose command.Based on the output, which two statements are correct? (Choose two.)  Anti-replay is enabled.  DPD is disabled.  Remote gateway IP is 10.200.4.1.  Quick mode selectors are disabled. Q99. The CLI command set intelligent-mode <enable | disable> controls the IPS engine’s adaptive scanning behavior. Which of the following statements describes IPS adaptive scanning?  Determines the optimal number of IPS engines required based on system load.  Downloads signatures on demand from FDS based on scanning requirements.  Determines when it is secure enough to stop scanning session traffic.  Choose a matching algorithm based on available memory and the type of inspection being performed. Configuring IPS intelligence Starting with FortiOS 5.2, intelligent-mode is a new adaptive detection method. This command is enabled the default and it means that the IPS engine will perform adaptive scanning so that, for some traffic, the FortiGate can quickly finish scanning and offload the traffic to NPU or kernel. It is a balanced method which could cover all known exploits. When disabled, the IPS engine scans every single byte.config ips global set intelligent-mode {enable|disable} endQ100. View the global IPS configuration, and then answer the question below.Which of the following statements is true regarding this configuration?  IPS will scan every byte in every session.  FortiGate will spawn IPS engine instances based on the system load.  New packets will be passed through without inspection if the IPS socket buffer runs out of memory.  IPS will use the faster matching algorithm which is only available for units with more than 4 GB memory. Q101. View the exhibit, which contains the output of get sys ha status, and then answer the question below.Which statements are correct regarding the output? (Choose two.)  The slave configuration is not synchronized with the master.  The HA management IP is 169.254.0.2.  Master is selected because it is the only device in the cluster.  port 7 is used the HA heartbeat on all devices in the cluster. Q102. Which ADVPN configuration must be configured using a script on FortiManager, when using VPN Manager to manage FortiGate VPN tunnels?  Set protected network to all  Enable AD-VPN in IPsec phase 1  Configure IP addresses on IPsec virtual interfaces  Disable add-route on hub Q103. View the exhibit, which contains a session entry, and then answer the question below.Which statement is correct regarding this session?  It is an ICMP session from 10.1.10.10 to 10.200.1.1.  It is an ICMP session from 10.1.10.10 to 10.200.5.1.  It is a TCP session in ESTABLISHED state from 10.1.10.10 to 10.200.5.1.  It is a TCP session in CLOSE_WAIT state from 10.1.10.10 to 10.200.1.1. Q104. View the exhibit, which contains the output of a BGP debug command, and then answer the question below.Which of the following statements about the exhibit are true? (Choose two.)  The local router’s BGP state is Established with the 10.125.0.60 peer.  Since the counters were last reset; the 10.200.3.1 peer has never been down.  The local router has received a total of three BGP prefixes from all peers.  The local router has not established a TCP session with 100.64.3.1. Q105. Examine the output from the ‘diagnose debug authd fsso list’ command; then answer the question below.diagnose debug authd fsso list -FSSO logons-IP: 192.168.3.1 User: STUDENT Groups: TRAININGAD/USERS Workstation: INTERNAL2. TRAINING. LAB The IP address 192.168.3.1 is NOT the one used by the workstation INTERNAL2. TRAINING. LAB.What should the administrator check?  The IP address recorded in the logon event for the user STUDENT.  The DNS name resolution for the workstation name INTERNAL2. TRAINING. LAB.  The source IP address of the traffic arriving to the FortiGate from the workstation INTERNAL2. TRAINING. LAB.  The reserve DNS lookup forthe IP address 192.168.3.1. Q106. Refer to the exhibit, which shows the output of diagnose sys session stat.Which statement about the output shown in the exhibit is correct?  There are two sessions that have not been removed in case of any out-of-order packets that arrive.  There are 166 TCP sessions waiting to complete the three-way handshake.  162 sessions have been deleted because of memory page exhaustion.  All the sessions in the session table are TCP sessions. Q107. Examine the output of the ‘get router info bgp summary’ command shown in the exhibit; then answer the question below.Which statement can explain why the state of the remote BGP peer 10.200.3.1 is Connect?  The local peer is receiving the BGP keepalives from the remote peer but it has not received any BGP prefix yet.  The TCP session for the BGP connection to 10.200.3.1 is down.  The local peer has received the BGP prefixed from the remote peer.  The local peer is receiving the BGP keepalives from the remote peer but it has not received the OpenConfirm yet. Q108. Examine the output of the ‘get router info ospf interface’ command shown in the exhibit; then answer the question below.Which statements are true regarding the above output? (Choose two.)  The port4 interface is connected to the OSPF backbone area.  The local FortiGate has been elected as the OSPF backup designated router.  There are at least 5 OSPF routers connected to the port4 network.  Two OSPF routers are down in the port4 network. on BROADCAST network there are 4 neighbors, among which 1*DR +1*BDR. So our FG has 4 neighbors, but create adjacency only with 2 (with DR and BDR). 2 neighbors DRother (not down).Q109. Refer to the exhibit, which contains the output of a debug command.If the default settings are in place, what can be concluded about the conserve mode shown in the exhibit?  FortiGate is currently blocking all new sessions regardless of the content inspection requirements or configuration settings due to high memory use.  FortiGate is currently allowing new sessions that require flow-based or proxy-based content inspection but is not performing inspection on those sessions.  FortiGate is currently blocking new sessions that require flow-based or proxy-based content inspection.  FortiGate is currently allowing new sessions that require flow-based content inspection and blocking sessions that require proxy-based content inspection. Q110. Four FortiGate devices configured for OSPF connected to the same broadcast domain. The first unit is elected as the designated router The second unit is elected as the backup designated router Under normal operation, how many OSPF full adjacencies are formed to each of the other two units?  1  2  3  4 Q111. View the exhibit, which contains the output of a debug command, and then answer the question below.Which of the following statements about the exhibit are true? (Choose two.)  In the network on port4, two OSPF routers are down.  Port4 is connected to the OSPF backbone area.  The local FortiGate’s OSPF router ID is 0.0.0.4  The local FortiGate has been elected as the OSPF backup designated router. Q112. Refer to the exhibit, which shows the output of diagnose sys session list.If the HA ID for the primary device is 0, what will happen if the primary fails and the secondary becomes the primary?  Traffic for this session continues to be permitted on the new primary device after failover, without requiring the client to restart the session with the server.  The secondary device has this session synchronized; however, because application control is applied, the session will be marked dirty and have to be re-evaluated after failover.  The session state will be preserved but the kernel will need to re-evaluate the session due to NAT being applied.  The session will be removed from the session table of the secondary device due to the presence of allowed error packets, which will force the client to restart the session with the server. https://community.fortinet.com/t5/FortiGate/Technical-Note-How-to-see-if-a-session-is-synced-in-HA/ta-p/194185Q113. An administrator has configured a dial-up IPsec VPN with one phase 2, extended authentication (XAuth) and IKE mode configuration. The administrator has also enabled the IKE real time debug:diagnose debug application ike-1diagnose debug enableIn which order is each step and phase displayed in the debug output each time a new dial-up user is connecting to the VPN?  Phase1; IKE mode configuration; XAuth; phase 2.  Phase1; XAuth; IKE mode configuration; phase2.  Phase1; XAuth; phase 2; IKE mode configuration.  Phase1; IKE mode configuration; phase 2; XAuth. https://help.fortinet.com/fos50hlp/54/Content/FortiOS/fortigate-ipsecvpn-54/IPsec_VPN_Concepts/IKE_Packet_Processing.htmQ114. Which two statements about OCVPN are true? (Choose two.)  Only root vdom supports OCVPN.  OCVPN supports static and dynamic IPs in WAN interface.  OCVPN offers only Hub-Spoke VPNs.  FortiGate devices under different FortiCare accounts can be used to form OCVPN. Reference:https://docs.fortinet.com/document/fortigate/6.0.0/cookbook/977344/one-click-vpn-ocvpnhttps://docs.fortinet.com/document/fortigate/6.2.9/cookbook/496884/overlay-controller-vpn-ocvpn Loading … NSE7_EFW-7.0 Dumps for success in Actual Exam: https://www.validbraindumps.com/NSE7_EFW-7.0-exam-prep.html --------------------------------------------------- Images: https://free.validbraindumps.com/wp-content/plugins/watu/loading.gif https://free.validbraindumps.com/wp-content/plugins/watu/loading.gif --------------------------------------------------- --------------------------------------------------- Post date: 2023-08-14 13:44:45 Post date GMT: 2023-08-14 13:44:45 Post modified date: 2023-08-14 13:44:45 Post modified date GMT: 2023-08-14 13:44:45