Updated Oct 24, 2024 Verified D-PSC-MN-23 dumps Q&As - 100% Pass [Q42-Q64] : Free valid test braindumps : http://free.validbraindumps.com

QUESTION 42
What distinguishes PowerScale Gen 6 nodes from earlier generations?

They offer better energy efficiency.

They provide enhanced virtualization support.

They have higher storage density.

They feature a more robust operating system.

QUESTION 43
In a Dell PowerScale Gen 6 cluster, which nodes work as a pair?

Nodes in slots 1 and 2

Nodes in slots 2 and 4

Nodes in slots 1 and 3

Nodes in slots 2 and 3

QUESTION 44
A platform engineer plans to set up a rack system for a Dell PowerScale cluster installation.
What is a requirement for the initial setup?

The rack system must have twelve independent 200-240 V power sources.

Power cords must be connected to four power distribution units within the rack cabinet.

The rack cabinet must have at least dual power supplies with power distribution.

Grounding lugs must be used for internal grounding within the chassis.

QUESTION 45
A platform engineer is adding three F600 nodes to a Dell PowerScale cluster.
What is a good practice when adding the nodes?

Wait 5 minutes between each additional node.

Manually reboot each node before joining.

Use the isi network output to show progress.

Join new nodes simultaneously.

QUESTION 46
A platform engineer needs to power down a Dell PowerScale node to perform an FRU replacement.
Which command should they run first before making the replacement?

isi_celog_monitor -a

isi_gather_info

isi healthcheck

isi_hwmon -s

QUESTION 47
How should a technician ensure that the PowerScale rack and subcomponents are grounded properly?

By using insulated gloves during the installation

Checking the grounding with a multimeter

Connecting each component to a separate ground source

Ensuring the data center floor is conductive

QUESTION 48
What is a key step when connecting nodes to the data center’s power supply during a PowerScale installation?

Using power cables of the shortest possible length to reduce resistance

Ensuring each node is connected to a different circuit breaker

Implementing power redundancy for each node

Labeling power cables according to the nodes they supply

QUESTION 49
When maintaining Customer Replaceable Units (CRUs) in a PowerScale node, what is important to ensure?

The cluster is in maintenance mode.

Proper static electricity discharge procedures are followed.

The firmware is updated post-installation.

All CRUs are tested individually before installation.

QUESTION 50
During the maintenance of PowerScale nodes, what is a Field Replaceable Unit (FRU)?

A component that can be replaced without sending the entire unit for repair

A software module that can be updated independently

A node that can be swapped with another in the cluster without downtime

An external device that enhances the node’s capabilities

QUESTION 51
Before a PowerScale node can be put into operation after maintenance, what is an essential task?

Performing a full system backup

Running a system health check

Restoring user data

Updating the node’s firmware

QUESTION 52
A customer has purchased a new Dell PowerScale cluster consisting of eight F600 nodes and four H5600 nodes.
What is required when installing these nodes?

Deep rack for the H5600 chassis

Step-up transformers for the H5600 nodes

At least one standard 40U-P rack

An additional 1U of space for cable management

QUESTION 53
What is the correct order of steps to repackage the shipping material for a Dell PowerScale cluster?

1. Stack the shipping bracket on the pallet. Place ramp section B upside-down on the pallet, then stack section A, right-side up.
2. Band the unit with shipping straps.
3. Apply the two collar sections to either side of the pallet and hold them in place with the package hood.
4. Stack the two folded outer sleeves above the ramp sections.
5. Lay each of the outer sleeves flat, then fold it lengthwise before collapsing the three sections.

1. Stack the shipping bracket on the pallet. Place ramp section B upside-down on the pallet, then stack section A, right-side up.
2. Apply the two collar sections to either side of the pallet and hold them in place with the package hood.
3. Lay each of the outer sleeves flat, then fold it lengthwise before collapsing the three sections.
4. Stack the two folded outer sleeves above the ramp sections.
5. Band the unit with shipping straps.

1. Lay each of the outer sleeves flat, then fold it lengthwise before collapsing the three sections.
2. Stack the shipping bracket on the pallet. Place ramp section B upside-down on the pallet, then stack section A, right-side up.
3. Stack the two folded outer sleeves above the ramp sections.
4. Apply the two collar sections to either side of the pallet and hold them in place with the package hood.
5. Band the unit with shipping straps.

1. Stack the two folded outer sleeves above the ramp sections.
2. Band the unit with shipping straps.
3. Apply the two collar sections to either side of the pallet and hold them in place with the package hood.
4. Lay each of the outer sleeves flat, then fold it lengthwise before collapsing the three sections.
5. Stack the shipping bracket on the pallet. Place ramp section B upside-down on the pallet, then stack section A, right-side up.

QUESTION 54
During the installation of racks for PowerScale, why is it important to ensure proper alignment and leveling?

To facilitate proper airflow and cooling

To ensure ease of access for future maintenance

To prevent physical strain on components

To optimize space utilization within the data center

QUESTION 55
Which components are considered key Field Replaceable Units (FRUs) in PowerScale nodes?
(Select two)

Hard drives

Power supplies

Cooling fans

Network cards

QUESTION 56
What is a critical aspect of external networking setup for PowerScale clusters?

Configuring VLANs

Ensuring compatibility with legacy systems

Implementing Quality of Service (QoS)

Establishing redundant connections

QUESTION 57
Which of the following features are associated with PowerScale Gen 6.5 nodes? (Select two)

Enhanced data deduplication

Improved flash technology

Advanced thermal design

Increased node capacity

QUESTION 58
During the replacement of a failed hard drive, a key FRU, what steps should be followed to ensure proper installation?

Verifying the drive firmware version matches the cluster

Ensuring the node is isolated from the network

Performing a full data backup

Confirming the slot and drive compatibility

QUESTION 59
What are key considerations when designing the networking architecture for a PowerScale cluster?
(Select two)

Network latency

Firewall configurations

Switch capacity

Subnet planning

QUESTION 60
When installing PowerScale Gen 6 nodes, what is an essential hardware capability to verify?

Compatibility with existing rack units

Adequate power supply units

Support for mixed-node clusters

Availability of expansion slots for future upgrades

QUESTION 61
What is the recommended action if a PowerScale node reports inconsistent data?

Isolate the node immediately and perform a data integrity scan

Reboot the node to clear any temporary issues

Remove the node from the cluster and replace it

Run a synchronization process with other nodes

QUESTION 62
A platform engineer needs to gather information about the configuration of a Dell PowerScale cluster. They are specifically interested in knowing which features are affected by upgrading firmware on a subset of the nodes.
Which command does the engineer need to execute?

isi upgrade cluster list

isi_upgrade_helper

isi upgrade cluster view

isi_gather_info

QUESTION 63
An organization has a cluster of F800 nodes running OneFS version 9.0. A platform engineer is planning to add a new node pool of F600 nodes. While unpacking the first F600 node, the IT manager notices two of the ten drive bays are empty and asks the platform engineer about it.
How should the platform engineer respond?

Sales order shows 8-drive nodes instead of 10-drive nodes

Two additional drives are packaged separately

Two empty drive bays are dedicated for L3 cache

F600 nodes only use 8 of the 10 drive bays

QUESTION 64
When preparing a node for operation post-maintenance, what is a key software-related step?

Reinstalling the node’s operating system

Restoring the node to its factory settings

Checking for and applying any available software updates

Reconfiguring user access permissions