Q12. Refer to the exhibit.

Based on the exhibit, what is the outcome when the “Collect System Information” button is clicked?

Q13. An organization is hosting storage protection solutions for multiple companies. Their solutions are based on a single VNX array. What is the maximum number of RecoverPoint clusters that can be deployed by the organization?

Q14. In order to perform dynamic resizing of a replication set, what is a requirement?

Q15. An administrator ran the capture load command on a RecoverPoint cluster during a high-load issue. However, the administrator forgot to capture the output. Where can the RecoverPoint Cluster Load report be located?

Q16. What is a supported method to re-image a Gen 6 RPA node?

Q17. An application is running on XtremlO replicating to another XtremlO using RecoverPoint with the following:
Journal size= 1.05 * (write traffic) * (rollback time in seconds) / (1 – image access log percentage) + (reserved for marking)
. Average write traffic = 5 Mb/s
. Required rollback time = 24 hours
What is the minimum required size for the Journal volume using the default parameters?

Q18. The production and remote copies of a Consistency Group are hosted on XtremlO arrays. During application testing of the remote copy, the Image Access log capacity does not advance.
Why is the Image Access log capacity static?

Q19. Refer to the exhibit.

Based on the exhibit, what describes the state in which RPA-3 must be in prior to selecting “Next” to advance the wizard?

Q20. A company’s host systems are configured with iSCSI HBAs and they want to directly attach the RPAs to a VNX. Which configuration will meet this requirement?

Q21. During the write phase of RecoverPoint replication, when does the RPA send an acknowledgement back to the write splitter?

Q22. Which environment settings can be changed in the System Modification wizard for an RPA connected to a VNX, VMAX, or a VPLEX?

Q23. A company is implementing a total of four VNXs; two at their production site and two at their disaster recovery site. In addition, the company wants to manage all clusters as one RecoverPoint system.
When installing the RecoverPoint cluster, what should be selected in the RecoverPoint Deployment Manager wizard?

Q24. Which factors should be considered when using Deployment Manager to connect a RecoverPoint cluster to an existing cluster?

Q25. An organization plans to connect three different sites over IP using a RecoverPoint cluster at each site. However, the cluster fails to connect. The network team has determined that the required IP routing and WAN connectivity is in place. The desired routing information is added while running the Deployment Manager wizard.
What is a possible cause for the failure?

Q26. During the Deployment Manager wizard, the system confirmed errors detected on one or more new RPAs. You resolve the errors and proceed to the zoning step.
Which step detected the errors?

Q27. While running the Deployment Manager Installer for a new cluster with two RPAs, you discover that one RPA is running a different version. Which action is required to resolve this issue?

Q28. A RecoverPoint administrator wants to add volumes from an unlicensed array to a RecoverPoint/EX cluster. Which supported RecoverPoint volume type(s) addresses the administrator’s requirement?

Q29. A Consistency Group contains a production and a remote copy. Both are provisioned from XtremlO arrays. Where are the snapshots that represent the point-in-time images kept during normal replication?

Q30. In order to perform dynamic resizing of a replication set, what is a requirement?

Q31. A RecoverPoint storage administrator needs to protect a mission-critical application. The application is stored on three volumes provisioned from a new VNX. Once the Consistency Group is created for the application, how many replication sets will the group contain?

Q32. A storage administrator has seen high-load events in their RecoverPoint environment. The administrator wants to review the performance data for the past week with RecoverPoint. In addition, the administrator wants the raw data saved to a spreadsheet to review and create graphs of system performance over a period of time.
Which CLI command should be used?

Q33. What is the correct sequence of steps for Snap-based replication on XtremIO?