Real 156-835 Exam PDF Test Engine Practice Test Questions [Q28-Q43]

4.5/5 - (2 votes)

Real 156-835 Exam PDF Test Engine Practice Test Questions

CheckPoint 156-835 Real 2023 Braindumps Mock Exam Dumps

QUESTION 28
What kind of cluster Dual-Site can be compared to?

Active-Standby or VSLS

VSLS only

Active-Active

Active-Standby only

QUESTION 29
Which file on Appliance includes information about Security Group?

/etc/chassisdb.json

/etc/sgdb.json

/etc/smodb.json

/etc/distutiljson

QUESTION 30
What is the throughput penalty of Security Group?

5% per member

Depends on the type of Appliance

10% per Security Group with no relation to amount of members

1% per member

QUESTION 31
Which is a valid requirement for a supported Maestro appliance?

10GBps and 40Gbps or 100Gbps card with double-VLAN and LLDP support

At least one 10GBps line card

Nothing special as Maestro supports any Check Point appliance

Line card with double-VLAN and LLDP support

QUESTION 32
What is the throughput penalty of Security Group?

5% per member

Depends on the type of Appliance

10% per Security Group with no relation to amount of members

1% per member

QUESTION 33
How many orchestrators may Dual-Site include”

2 or 4

Only 4

QUESTION 34
What will happen in case of NAT of the traffic passing through Management network?

This traffic will not pass correction, since it will be dropped

This traffic will pass with no inspection

Since Management traffic is always going to SMO, it will take a care for Correction Layer and will re-distribute traffic to other Appliances

Orchestrator will disable NAT and traffic will pass with no issue

QUESTION 35
What kinds of transceivers are supported on Orchestrator MHO-170?

QSFP. QSFP28

SFP. SFP+. SFP28

SFP+, SFP28. QSFP

SFP. QSFP, QSFP28

QUESTION 36
What is the default IP range of CIN network (with no increment)?

192.168.1.0

198 .51 .100. 0

The same as Management network

192. 0 .2 .0

QUESTION 37
What is the basic installation sequence of the Orchestrator in case of single Orchestrator?
1. Create a Security Group
2. Configure Default Gateway
3. Connect with Serial Console cable to the Orchestrator
4. Configure IP for one of its Management interfaces
5. Connect an appliance to a downlink port
6. Change Orchestrator amount to 1
7. Browse to the Orchestrator’s WebUI

3-4-2-6-5-7-1

3-1-7-2-4-6-5

1-4-2-5-7-3-6

7-4-2-5-3-1-6

QUESTION 38
When running ifconfig command on an Appliance, there are interfaces shown in the list: ethl-Sync and eth2-Sync. What is the purpose of these interfaces?

These interfaces are bond members (slaves) of Sync Bond

These interfaces can be used as backup for Sync interface

These interfaces are not in use. Security GW module use Sync interface for synchronization

These interfaces represent physical Sync interface at the front panel of appliance

QUESTION 39
What is the minimal amount of cables needed in order to connect an Appliance to an Orchestrator?

Three cables: uplink, downlink, SYNC

One Downlink cable only

Two cables: one uplink and one downlink

Four cables: uplink, downlink, SYNC and Management

QUESTION 40
In case of VSX: What is the right command to see overall performance details of all Appliances within the Security Group and all Virtual Systems?

asg pert -v -p

asg pert -vs all -v -vv

asg pert -v

asg pert -vs enabled -p

QUESTION 41
What is the Sync network on Appliances used for?

May be used for any purpose, but synchronization always have priority

To synchronize configurations and connections in between connection tables of different Appliances

To transfer configuration files from Orchestrators to Appliances

To transfer data in case of full utilization of the downlink interfaces

QUESTION 42
There are two 10Gbps dual-port NICs and one 40Gbps NIC installed on a 23800 Appliance in slots 1, 2 and 3 accordingly. Which interfaces should be connected to Orchestrator 1 for downlinks’ intra-orchestrator redundancy when using two Orchestrators?

Any pair of available ports

Port 1 in Slot 2 and Port 2 in Slot 1

Port 1 in Slot 1 and Port 2 in Slot 1

This configuration is not supported

QUESTION 43
What is the distribution mode?

Distribution mode is the same as QSFP mode

Distribution mode is how the Orchestrator distributes traffic in between Security Groups

Distribution mode means selected algorithm for traffic distribution in between Orchestrators

Distribution mode means selected algorithm for traffic distribution in between Appliances

Loading …

Prepare For The 156-835 Question Papers In Advance: https://www.validbraindumps.com/156-835-exam-prep.html

Free valid test braindumps

Real 156-835 Exam PDF Test Engine Practice Test Questions [Q28-Q43]

Leave a Reply Cancel reply