100% Pass Top-selling API-SIEE Exams – New 2026 API Pratice Exam [Q28-Q49]

5/5 - (1 vote)

100% Pass Top-selling API-SIEE Exams – New 2026 API Pratice Exam

ICP Programs Dumps API-SIEE Exam for Full Questions – Exam Study Guide

API API-SIEE Exam Syllabus Topics:

Topic	Details
Topic 1	Equipment Risk Assessment: Focuses on developing inspection project plans, inspection and test plans, and reviewing reports to assess equipment risk.
Topic 2	Electrical Inspection Tools and Test Equipment: Covers the tools and test equipment used by inspectors to perform electrical source inspections.
Topic 3	Terms and Definitions: Covers the foundational terminology and definitions used throughout electrical source inspection work.
Topic 4	Source Inspection Performance: Covers inspector conduct, safety, project document review, report writing, and handling nonconformances and deviations during inspections.
Topic 5	Electrical Skid Mounted Equipment: Addresses inspection of skid-mounted assemblies including hazardous location equipment, grounding, cable systems, control wiring, and applicable codes.

NEW QUESTION 28
According to NFPA 70, equipment shall be marked to show the hazardous environment for which it has been evaluated. Markings on this equipment shall include which of the following?

Class, voltage, current, material of construction, equipment temperature

Class, division, material classification group, equipment temperature, ambient temperature range

Class, voltage, material classification group, operating temperature, ambient temperature range

Class, division, material of construction, equipment temperature, ambient temperature range

NEW QUESTION 29
What is the process that aims to find potential defects in a product before it is released for delivery?

Inspection

Examination

Quality Control

Quality Assurance

NEW QUESTION 30
Laminations in a motor stator core are used to reduce:

AC voltage.

frequency.

energy loss.

DC voltage.

NEW QUESTION 31
What method is used to verify tightness of accessible bolted electrical connections?

Compression of the lock-nut

Visual inspection of torque markings

Verification of assembly check sheet

Calibrated torque wrench

NEW QUESTION 32
What document provides information on design and installation of electrical systems for fixed and floating offshore petroleum facilities for unclassified and Class I, Zone 0, Zone 1 and Zone 2 locations?

NFPA 70

IEEE 841

API RP 14F

API RP 14FZ

NEW QUESTION 33
Inspections, examinations, and tests must be performed in accordance with the source Inspection Test Plan, project specification, applicable codes and standards and meet:

published catalog data.

manufacturer’s standard.

the applicable acceptance criteria.

commonly accepted industry practice.

NEW QUESTION 34
The cosine of the difference in phase angle between voltage and current is:

power factor.

real power.

apparent power.

mho.

NEW QUESTION 35
According to NFPA 70, the number of bends permitted between pull points for rigid metal conduits RMC shall not be more than:

the equivalent of six quarter bends.

the equivalent of four quarter bends 360 degrees total.

four bends provided the radii is less than 5 times the conduit diameter.

four bends provided the bend radii is at least 10 times the conduit diameter for conduit greater than 3/4 inch 19 mm.

NEW QUESTION 36
A source inspector reviewing a control panel should verify wiring against which project document as a core inspection activity?

Employee training log

One-line wiring diagram

Freight invoice

Packing list only

NEW QUESTION 37
Which item is part of typical final inspection and shipping preparation for a liquid-immersed transformer?

Verification that all FAT issues are resolved

Reclassification of the project risk register

Reissue of procurement bid tabs

Elimination of all documentation requirements

NEW QUESTION 38
According to NETA, for low voltage cables a visual inspection must verify that:

color codes comply with IEEE requirements.

the shield on power cables is properly grounded.

connections are in accordance with the single-line diagram.

all cables are connected to terminals via ring tongue lugs.

NEW QUESTION 39
Which information should be included at a minimum in a source inspection report?

Inspector’s travel reimbursement total

Reference drawings/data used, including drawing numbers

Supplier profit margin

Internal purchaser budget code only

NEW QUESTION 40
According to IEEE 841, terminal boxes for voltages above 1000 V or for frame sizes exceeding 449T at 1000 V shall be provided with:

integrally designed grounding lugs.

permanent locking mechanism.

corrosion-resistant replaceable automatic drainage fitting.

corrosion-resistant non-sparking coating.

NEW QUESTION 41
What is an insulation resistance test?

A test that determines the adequacy of electrical insulation for the normally occurring over voltage transient

A test that determines the corrosive contaminants around the conductors, terminal spacing problems, and tolerance errors in cables

A spot overvoltage test which uses an applied DC voltage to measure ohms

A test that determines the voltage that electrical insulation can withstand during normal operation

NEW QUESTION 42
When might a resident source inspector be required at a shop during manufacture and fabrication?

When the risk assessment classifies the equipment item as highest risk

When the item is procured from a foreign source

When the source inspector would have to travel long distances each day to the shop

When the shop is fully loaded with items to be fabricated and schedule is tight

NEW QUESTION 43
Why should the dates for source inspection scheduled work process events such as the pre-inspection meeting, key inspection events and anticipated shipping date be identified in advance?

To allow coordination with other project members involved in the activity

To ensure that all dates will meet the project schedule and quality requirements

To provide a sound basis for inspection and test planning for each shop

To be able to assign inspectors to the shops in order not to conflict with other projects

NEW QUESTION 44
During the course of manufacturing the supplier/vendor may propose design changes that could impact cost, schedule and/or quality. In such cases, the source inspector should:

prepare a summary of the changes made for inclusion in their report and subsequent action by the purchaser.

request that the supplier/vendor develop a cost/benefit analysis for review and approval by the inspector.

prepare a cost/benefit analysis in order to justify their acceptance or rejection of the proposed changes.

request that the supplier/vendor propose such changes in writing for review by the purchaser.

NEW QUESTION 45
According to API 541, when specified, shipping preparations shall make the equipment suitable for outdoor storage from the time of shipment for at least:

three months.

six months.

nine months.

twelve months.

NEW QUESTION 46
Metallic shielding components such as tapes, wires, or braids shall be connected to a:

equipment grounding busbar.

low voltage ceramic insulator.

low voltage connector.

center tap of a transformer.

NEW QUESTION 47
What is the common industry term used for the dielectric withstand test?

Hipot test

Voltage test

Current test

Capacitor microfarad dielectric test

NEW QUESTION 48
Which of the following tools is used for inspection of coating?

Dry film thickness DFT

Digital surface profile gauge

Surface profile replica tape

Ultrasonic thickness meter

NEW QUESTION 49
What is the purpose of a clamp meter?

To measure the magnetic field around a conductor

To test that the electrical equipment maximum temperature does not exceed the ignition temperature of gases in the environment

To externally measure the sum of the current flowing through the cable

To verify the process temperature and the equipment temperature have the same Class 1 rating

Authentic Best resources for API-SIEE Online Practice Exam: https://www.validbraindumps.com/API-SIEE-exam-prep.html

Free valid test braindumps

100% Pass Top-selling API-SIEE Exams – New 2026 API Pratice Exam [Q28-Q49]

API API-SIEE Exam Syllabus Topics:

Leave a Reply Cancel reply